DrivePro Body Toolbox Gebruiksaanwijzing (Windows)


1. System Requirements

!!! note Voor Windows OS - Microsoft .Net framework 4.6.1 of hoger installatie vereist.

2. Hardware Requirements

3. Supported Models

Body Camera's

4. Status

Op de Status pagina wordt de basisinformatie van DrivePro™ Body weergegeven, inclusief gebruikerslabel, modelnaam, serienummer apparaat, firmwareversie, teamsynchronisatiegroep, resterende opslagruimte en batterijniveau.

5. Instellingen

Op de pagina Instellingen kunt u de apparaatinstellingen, video-instellingen en video-stempel aanpassen.

Apparaat instellingen

Video instellingen

Video stempel

6. Hulpmiddelen

Op de pagina Hulpmiddelen, kunt u de firmware updaten naar de nieuwste versie, schijf formatteren of de DrivePro Boy opnieuw instellen.

!!! note Opmerking - Door de schijf formatteren en het apparaat opnieuw in te stele, worden alle gegevens permanent verwijderd.

7. Bestandsbeheer

Op de pagina Bestandsbeheer kunt u uw video's en foto's zoeken, beheren of foto's bewerken.

8. Slimme detectie

  1. Ga naar “Smart Detection” in het hoofdmenu.

  2. Selecteer een bestand in de bestandenlijst, de analysevoortgang start automatisch om de gezichten in een video te identificeren en beeldmateriaal naar de zijbalk te extraheren.

  3. Selecteer beeldmateriaal om een momentopname te maken of schakel over naar de redactiemodus.

  4. Klik op “Snapshot” om een snapshot te maken, de snapshot wordt opgeslagen in dezelfde map als de geselecteerde video.

  5. Klik op “Redactie” om over te schakelen naar de redactiemodus.

  6. In de redactiemodus kun je maximaal 10 beelden selecteren om te vervagen.

  7. Klik op “Toepassen” om het redactieproces te starten na het selecteren van de beelden. U kunt ervoor kiezen om audiotracks te verwijderen of niet.

  8. Wacht tot het proces is voltooid. De geredigeerde video wordt opgeslagen in dezelfde map als de geselecteerde video.

9. Webcam modus

!!! note Opmerking - Momenteel ondersteunt alleen DrivePro Body 30/60 deze functie.

  1. Klik op om naar de webcammodus te gaan.

  2. Overschakelen naar webcammodus.

  3. Klik op om de webcam-testpagina te openen.

  4. Controleer op de webcamtestpagina of het livebeeld goed is.

  5. Klik op om de microfoontestpagina te openen.

  6. Controleer op de microfoontestpagina of de microfoon normaal geluid ontvangt.

  7. Na het voltooien van de test, vergeet niet te klikken op of om de testpagina af te sluiten.

  8. Om de webcammodus te verlaten, klikt u op , de instructiepagina voor het verlaten van de webcammodus verschijnt.

10. Team Sync

!!! note Note - Currently, only DrivePro Body 30/60 supports this feature.

“Team Sync” is a function based on the Bluetooth technology, as soon as one body camera enters the recording mode from the buffering mode; all other cameras in the same group automatically enter the recording mode as well.

Please refer to the following procedure if you would like to enable the “Team sync” function.

  1. Please connect your DrivePro Body 30/60 to the computer and run DrivePro Body Toolbox.

    DrivePro Body Toolbox: https://nl.transcend-info.com/Support/Software-184/

  2. Please click on “Edit User Label”, and set “Team sync” from “Off” to “ your preferred team number” based on your needs, you may select from 1 ~ 10 under Team Sync.

  3. After the settings are completed, you may remove your DrivePro Body from the computer.

11. Bluetooth wakeup

!!! note Note - Currently, only DrivePro Body 60 supports this function.

“Bluetooth wakeup” is a more advanced function than “Team sync”. Once Leader body camera enters the recording mode, all other cameras in the same group will automatically enter the recording mode from off status as well.

Please refer to the following steps if you want to enable the “Bluetooth wakeup” function.

  1. Please connect your DrivePro Body 60 to the computer and run the DrivePro Body Toolbox.

    DrivePro Body Toolbox: https://nl.transcend-info.com/Support/Software-184/

  2. Please click on “Edit User Label”, select your team number, and check off “Leader” to enable the “Bluetooth wakeup” function.

  3. Once the settings are completed, you may remove DrivePro Body from the computer.

12. Voorkeur

Klik op bovenaan de pagina om de instellingen van de DrivePro™ Body Toolbox aan te passen. Controleer de beschikbare opties hieronder volgens uw voorkeur.

Optie Instructies
Automatisch uitvoeren bij opstarten van Windows DrivePro Body Toolbox start automatisch wanneer de computer wordt aangezet.
Minimaliseren bij opstarten DrivePro Body Toolbox wordt automatisch geminimaliseerd in de verborgen werkbalk bij het opstarten.
Taal Displaytaal DrivePro Body Toolbox.
Auto back up Automatisch een back-up maken van DrivePro Body-apparaatbestanden die op de computer zijn aangesloten.
Formatteer de schijf nadat de back-up is voltooid Nadat de back-up is voltooid, wordt de DrivePro Body-opslagruimte automatisch geformatteerd.
Beveiligde gegevens Plaats de back-up bestanden in een niet-gedeelde map voor opslag.
Methoden voor het benoemen van back-upmappen De naam van de map waarin de back-upbestanden zijn opgeslagen, u kunt “Apparaat-ID” of “Gebruikersnaam” kiezen om deze een naam te geven.
Back-up pad Opslag locatie voor back-up bestanden.
Automatische synchronisatietijd met pc Synchroniseer automatisch de tijd van het DrivePro Body-apparaat dat op de computer is aangesloten.


More Help

If you cannot find the answer to your problem in this manual and are having difficulty with DrivePro Body software or Transcend’s Body Cameras, please visit our Tech Support website at http://nl.transcend-info.com/Support/contact_form